Brother NX-200 Manuel d'utilisateur Page 13
- Page / 111
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
7
GETTING READYCONTENTS SEWING BASICS UTILITY STITCHES APPENDIX INDEX
FOR USERS IN THE UK, EIRE, MALTA AND CYPRUS ONLY
If this machine is fitted with a three-pin non-rewireable BS plug then please read the following.
IMPORTANT
If the available socket outlet is not suitable for the plug supplied with this equipment, it should be cut
off and an appropriate three-pin plug fitted. With alternative plugs an approved fuse must be fitted in
the plug.
NOTE
The plug served from the main lead must be destroyed as a plug with bared flexible cords is
hazardous if engaged in a live socket outlet. In the event of replacing the plug fuse, use a fuse
approved by ASTA to BS 1362, i.e. carrying the mark, rating as marked on plug.
Always replace the fuse cover, never use plugs with the fuse cover omitted.
WARNING
DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE
LETTER ‘E’, BY THE EARTH SYMBOL OR COLOURED GREEN OR GREEN AND YELLOW.
The wires in this main lead are colored in accordance with the following code:
Blue Neutral
Brown Live
As the colors of the wiring in the main lead of this appliance may not correspond with the colored
markings identifying the terminals in your plug, proceed as follows.
The wire which is colored blue must be connected to the terminal which is marked with the letter
‘N’ or colored black or blue.
The wire which is colored brown must be connected to the terminal which is marked with the letter
‘L’ or colored red or brown.
F0_brotherE.book Page 7 Wednesday, May 21, 2003 11:38 AM
- Enclosed Accessories 2
- Front view 3
- Needle and presser foot 4
- Right-side/rear view 4
- Operation buttons 5
- Operation panel 6
- Optional Accessories 7
- Introduction 8
- Sewing Machine Features 8
- Contents 9
- SAVE THESE INSTRUCTIONS 12
- Important Safety Instructions 12
- IMPORTANT 13
- GETTING READY 15
- Turning the Machine On/Off 16
- Turning on the machine 17
- Turning off the machine 17
- Winding/Installing the Bobbin 18
- 1 Sewing speed controller 21
- 1 Start/stop button 21
- Installing the bobbin 22
- Upper Threading 24
- Upper Threading 19 25
- Threading the needle 27
- Using the twin needle 28
- Upper Threading 23 29
- Using thread that winds off 30
- Pulling up the bobbin thread 31
- Replacing the Needle 32
- Checking the needle 33
- Replacing the needle 34
- Replacing the Presser Foot 35
- Adjusting the pressure of 36
- Removing the presser foot 37
- Using the optional walking 37
- 1 Needle position button 38
- 1 Presser foot lever 38
- Stitching cylindrical pieces 39
- Sewing large pieces of fabric 39
- SEWING BASICS 41
- General sewing procedure 43
- Positioning the fabric 44
- Starting to sew 45
- Securing the stitching 47
- Cutting the thread 49
- Adjusting the Thread Tension 50
- Adjusting the stitch width 51
- Adjusting the stitch length 52
- Useful Functions 53
- Useful Sewing Tips 55
- Sewing thick fabrics 56
- Sewing thin fabrics 57
- Sewing stretch fabrics 57
- Sewing an even seam 57
- UTILITY STITCHES 59
- Selecting Stitching 60
- Selecting Stitching 55 61
- Overcasting Stitches 62
- Overcasting Stitches 57 63
- 1 2 cm (1/16 inch) 65
- 1 Guide plate 65
- 1 5 mm (3/16 inch) 65
- Basic Stitching 66
- Blind Hem Stitching 67
- Buttonhole Stitching 69
- Buttonhole sewing 70
- Buttonhole Stitching 65 71
- Button sewing 73
- 1 Button 74
- 1 Back side 74
- Buttonhole Stitching 69 75
- Zipper Insertion 76
- Inserting a side zipper 77
- Zipper Insertion 73 79
- Stretch stitching 80
- Elastic attaching 80
- Appliqué stitching 83
- Patchwork (crazy quilt) 84
- Quilting 85
- Free-motion quilting 86
- 1 Feed dog position switch 87
- 2 Back side 87
- 1 Pattern 87
- Reinforcement Stitching 88
- Reinforcement Stitching 83 89
- Eyelet Stitching 90
- Decorative Stitching 91
- Fagoting 92
- Scallop stitching 93
- Smocking 93
- Heirloom stitching 95
- 1 4 mm (3/16 inch) 96
- APPENDIX 97
- Stitch Settings 98
- Stitch Settings 93 99
- Stitch Settings 95 101
- Maintenance 102
- Troubleshooting 104
- Error messages 107
- Operation beep 108
- Removing the upper cover 108
- XC4665-0511 111
- Printed in Taiwan 111
Produits connexes et manuels pour Machines à coudre Brother NX-200
(90 pages)
(146 pages)
(2 pages)
© 2020, manymanuals.fr. Tous droits réservés | 3.960 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels