Brother NX-200 Manuel d'utilisateur Page 104
- Page / 111
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
APPENDIX —————————————————————————————————————————————————————————
—
98
GETTING READYCONTENTS SEWING BASICS UTILITY STITCHES APPENDIX INDEX
Troubleshooting
If the machine stops operating correctly, check the following possible problems before requesting service.
If the problem persists, contact your retailer or the nearest authorized service center.
Symptom Probable Cause Remedy Reference
The sewing
machine does
not operate.
The machine is not turned on. Turn on the machine. page 11
The start/stop button was not
pressed.
Press the start/stop button. page 39
The presser foot lever is raised. Lower the presser foot lever.
–
The start/stop button was pressed,
even though the foot controller is
connected.
Do not use the start/stop button
when the foot controller is con-
nected. To use the start/stop button,
disconnect the foot controller.
page 39
The needle
breaks.
The needle is incorrectly installed. Correctly install the needle.
page 28The needle clamp screw is loose.
Use the screwdriver to firmly tighten
the screw.
The needle is bent or blunt. Replace the needle.
The combination of fabric, thread
and needle is not correct.
Select a thread and needle that are
appropriate for the type of fabric
being sewn.
page 26
The presser foot that is used is not
appropriate for the type of stitch that
you wish to sew.
Attach the presser foot that is appro-
priate for the type of stitch that you
wish to sew.
page 92
The upper thread tension is too tight. Loosen the upper thread tension. page 44
The fabric is pulled too much. Lightly guide the fabric.
–
The spool is incorrectly installed. Correctly install the spool. page 18
The area around the hole in the nee-
dle plate is scratched, or has a burr
on it.
Replace the needle plate.
Contact your retailer or the nearest
authorized service center.
–
The area around the hole in the
presser foot is scratched, or has a
burr on it.
Replace the presser foot.
Contact your retailer or the nearest
authorized service center.
–
The shuttle is scratched, or has a
burr on it.
Replace the shuttle.
Contact your retailer or the nearest
authorized service center.
–
A bobbin designed specifically for
this machine is not used.
Incorrect bobbins will not work
properly. Only use a bobbin
designed specifically for this
machine.
page 12
F0_brotherE.book Page 98 Wednesday, May 21, 2003 11:38 AM
- Enclosed Accessories 2
- Front view 3
- Needle and presser foot 4
- Right-side/rear view 4
- Operation buttons 5
- Operation panel 6
- Optional Accessories 7
- Introduction 8
- Sewing Machine Features 8
- Contents 9
- SAVE THESE INSTRUCTIONS 12
- Important Safety Instructions 12
- IMPORTANT 13
- GETTING READY 15
- Turning the Machine On/Off 16
- Turning on the machine 17
- Turning off the machine 17
- Winding/Installing the Bobbin 18
- 1 Sewing speed controller 21
- 1 Start/stop button 21
- Installing the bobbin 22
- Upper Threading 24
- Upper Threading 19 25
- Threading the needle 27
- Using the twin needle 28
- Upper Threading 23 29
- Using thread that winds off 30
- Pulling up the bobbin thread 31
- Replacing the Needle 32
- Checking the needle 33
- Replacing the needle 34
- Replacing the Presser Foot 35
- Adjusting the pressure of 36
- Removing the presser foot 37
- Using the optional walking 37
- 1 Needle position button 38
- 1 Presser foot lever 38
- Stitching cylindrical pieces 39
- Sewing large pieces of fabric 39
- SEWING BASICS 41
- General sewing procedure 43
- Positioning the fabric 44
- Starting to sew 45
- Securing the stitching 47
- Cutting the thread 49
- Adjusting the Thread Tension 50
- Adjusting the stitch width 51
- Adjusting the stitch length 52
- Useful Functions 53
- Useful Sewing Tips 55
- Sewing thick fabrics 56
- Sewing thin fabrics 57
- Sewing stretch fabrics 57
- Sewing an even seam 57
- UTILITY STITCHES 59
- Selecting Stitching 60
- Selecting Stitching 55 61
- Overcasting Stitches 62
- Overcasting Stitches 57 63
- 1 2 cm (1/16 inch) 65
- 1 Guide plate 65
- 1 5 mm (3/16 inch) 65
- Basic Stitching 66
- Blind Hem Stitching 67
- Buttonhole Stitching 69
- Buttonhole sewing 70
- Buttonhole Stitching 65 71
- Button sewing 73
- 1 Button 74
- 1 Back side 74
- Buttonhole Stitching 69 75
- Zipper Insertion 76
- Inserting a side zipper 77
- Zipper Insertion 73 79
- Stretch stitching 80
- Elastic attaching 80
- Appliqué stitching 83
- Patchwork (crazy quilt) 84
- Quilting 85
- Free-motion quilting 86
- 1 Feed dog position switch 87
- 2 Back side 87
- 1 Pattern 87
- Reinforcement Stitching 88
- Reinforcement Stitching 83 89
- Eyelet Stitching 90
- Decorative Stitching 91
- Fagoting 92
- Scallop stitching 93
- Smocking 93
- Heirloom stitching 95
- 1 4 mm (3/16 inch) 96
- APPENDIX 97
- Stitch Settings 98
- Stitch Settings 93 99
- Stitch Settings 95 101
- Maintenance 102
- Troubleshooting 104
- Error messages 107
- Operation beep 108
- Removing the upper cover 108
- XC4665-0511 111
- Printed in Taiwan 111
Produits connexes et manuels pour Machines à coudre Brother NX-200
(90 pages)
(146 pages)
(2 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.496 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels