Brother BES-941BC Manuel d'instructions Page 56
- Page / 193
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
BES-941BC • BES-1241BC
54
Chapter 2 Embroidering Procedures
HOOP
FLAT CAP
Selects the flat or cap hoop. This selection should be done before turning the power ON
to the machine. The setting will not be changed if the selection is done after turning the
power OFF.
Moves the hoop.
Step-back or forward is available during suspension. (Use switches only.)
Changes the speed range during embroidering (Use switches only).
Carries out inching of the hoop when the switch is pressed in the inching mode.
Move the cursor for selecting sewing data and an icon.
Moves the needle bar. The needle moves by the diameter every time this switch is pressed.
Change to the screen for selecting sewing data.
Operation panel
Contrast volume
Adjusts the screen contrast.
SBUS interface connector
Not used (Do not connects anything.)
RS-232C interface connector
Connect personal computer with BE-100 installed, etc.
- BES-941BC 1
- BES-1241BC 1
- SAFETY INSTRUCTIONS 3
- Installation 4
- Environmental requirements 4
- Cleaning 6
- Maintenance and inspection 6
- DANGER GEFAHR 7
- Belt cover 8
- Finger guard 8
- Before Starting Operation 9
- BES-941BC • BES-1241BC 10
- Explanation of models 11
- Configuration of this manual 11
- Chapter 10 Troubleshooting 12
- Screen Composition 14
- Contents 16
- Chapter 5 Setting 17
- Chapter 1 21
- 1. Specifications 22
- BES-941BC 23
- BES-1241BC 23
- Accessories 24
- 3. Installation 25
- When using a crane 26
- 3-2 Installation of Machine 27
- 3-4 Mounting of Table 30
- 3-5 Mounting of Cotton Stand 34
- 3-7 Grounding 37
- 4-1 Upper Threading 38
- No.2,5,8,11 39
- No.1,4,7,10 39
- Needle Bar No.3,6,9,12 39
- 4-2 Replacement of Bobbin 41
- * Correct adjustment 50
- Lower thread tension 51
- Chapter 2 53
- Embroidering Procedures 53
- Functions of Operation Panel 54
- FLAT CAP 56
- Switches at Machine Heads 57
- Switches on Tension Plate 57
- Turn on the Machine Power 60
- Retrieve the Embroidery Data 61
- Start Embroidering 61
- Chapter 3 63
- What Can the Machine Do? 64
- Selection of Data 65
- Access lamp 66
- Eject switch 66
- Reading from Memory 68
- Currently displayed screen 70
- No. of screens to be selected 70
- 9. Press 75
- four times 75
- 10. Press 75
- Feedhold 77
- Cancellation 77
- Step Forward and Step-Back 78
- For Step Forward (Back) 79
- Resuming Sewing 79
- Writing the embroidering data 80
- Chapter 4 81
- Editing of Embroidering Data 81
- Rotation 83
- Enlargement and Reduction 84
- is reversed in black 85
- Up/down mirror patter 86
- Right/left mirror patter 86
- Right/Left Mirror Pattern 87
- Up/Down Mirror Pattern 87
- Repetition 88
- 4. Press 89
- 7. Press 89
- Other Editing 90
- Thread Trimming Feed Number 91
- Swing Width Correction 91
- after setting is finished 92
- Setting of Needle Bars 96
- Thread Breakage Sensor 97
- Automatic Step-Back 98
- Number of stitches 99
- Setting of Machine 100
- Speed Range 101
- Speed of Each Speed Range 102
- Setting of Mending 103
- Chapter 5 Setting 104
- Modify this figure 104
- Thread Trimming Length 105
- Thread Withdrawal Feed Length 105
- Sewing Area 107
- Hoop Retract Point 108
- Hoop Automatic Retract 109
- Setting of Environment 110
- Checking the Embroidery Area 111
- Power Voltage 112
- Display Language 113
- Alarm Sound 114
- Motive Speed 115
- Small-Pitch Deletion 116
- Release B1 error 117
- When the boring mode is valid 118
- Lock Stitch 119
- Validating the lock stitch 120
- Invalidating the lock stitch 120
- Speed Limit in a Short Pitch 122
- Feed Timing 123
- Automatic Input Setting 124
- . Press 126
- Display of Information 127
- Features of Machine 128
- Information about Versions 129
- 1. Operating Procedures 132
- 2. Machine Stop 133
- 3-1 Remedies 134
- 3-2 Mending 135
- 4. Jog Embroidering 137
- 5. Hoop Feed Position 137
- 6. Area Check 138
- 7. Jog Switches 139
- 8. Detection of Zero Point 141
- Chapter 7 Maintenance 143
- 1. Cleaning 144
- 1-2 Cleaning of Needle Plate 145
- 2. Oiling 146
- 3. Greasing 148
- Chapter 7 Maintenance 149
- 3-2 Feed Guide Section 152
- Chapter 8 Adjustment 153
- Chapter 8 Adjustment 155
- 2-1 Replacing Rotary Hook 158
- 123456789 159
- 6-1 Attaching the Fixed Knife 162
- 7. Adjusting the Belt Tension 164
- 8. Thread Wiper Adjustment 165
- Chapter 9 Error code list 167
- Chapter 10 Troubleshooting 173
- Mechanical Section 174
- Problem Check Point 175
- Check these points once again 175
- Electrical Section 176
- Symptom Measures 177
- Connection and Installation 185
- Attaching Bobbin Winder 186
- Lines(A) 188
- Removing the rear covers 190
- Removing the cover LE 191
- INSTRUCTION MANUAL 193
Produits connexes et manuels pour Machines à coudre Brother BES-941BC
(2 pages)
(21 pages)
(196 pages)
(1 pages)
(40 pages)
(183 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.529 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels