Brother PT-80 Manuel d'utilisateur télécharger pdf

brother.

OCD

o o o a o o o o o' o" o“

oooooooooo

ooooooooo

(

iuciMW*“«“***’'*”"

PT-80

USER'S GUIDE

English

/ Español

Printed in China

LN8233001®

www.brother.com

INTRODUCTION

With your PT-80, you can create labels for any application. Select from the

many frames, character sizes and styles to design beautiful custom labels. In

addition, the variety of tape cartridges available allows you to print labels with

different widths and exciting colors.

Read this manual carefully before starting and keep the manual in a handy

place for future reference.

FCC NOTICE

This device compiles with Part 15 of the FCC Rules. Operation is subject to the following fwo conditions: (1)

This device may not cause harmful Interference, and (2) this device must accept any interference received,

Including Interference that may cause undesIred operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

Interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the Instructions, may cause harmful Interference to

radio communications. However, there is no guarantee that Interference will not occur In a particular

Installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment Into an outlet on a circuit different from that to which the receiver Is connected.

- Consult the dealer or an experienced radio/TV technician for help.

- Changes or modifications not expressly approved by Brother Industries, Ltd. could void the user’s

authority to operate the equipment.

GENERAL PRECAUTIONS

Use only Brother M tapes with this machine. Do not use tapes that do not have

the ^ mark.

Do not clean the machine with alcohol or other organic solvents. Only use a soft, dry

cloth.

Do not touch the print head mechanism. Use a soft wipe (e.g. a cotton swab) when

cleaning the print head.

To avoid injuries, do not touch the cutter's edge.

To prevent damage or breakage of the LCD glass, do not press on the display.

Do not put any foreign objects into or heavy objects on the machine.

Do not leave any rubber or vinyl on the machine for an extended period of time,

otherwise the machine may be stained.

Do not get the machine wet, such as by handling the machine with wet hands or

spilling beverages on to the machine.

Do not expose the machine to extremely high temperatures or high humidity. Never

leave It on the dashboard, In the back of your car, near heaters or other hot

appliances. Keep It out of both direct sunlight and rain.

Avoid using the machine In extremely dusty places.

Depending on the environmental conditions and the applied settings, some

characters or symbols may be difficult to read.

Do not pull on the tape being fed from the P-touch iabeier, otherwise the tape

cassette or P-touch Iabeier may be damaged.

Do not attempt to cut the tape while printing or feeding since this will damage the tape.

Do not try to print labels using an empty tape cassette set in the P-touch labeler. Doing

so will damage the print head.

Remove the batteries if you do not intend to use the machine for an extended period

of time. (Note: When power Is disconnected for more than two minutes, all text and

format settings will be cleared. Language, unit and clock settings will also be cleared.)

Make sure that the power Is turned off when replacing batteries or tape cassette.

Do not use old and new batteries together or mix alkaline batteries with other type

batteries, or set the positive and negative end in the wrong position. Otherwise, the

batteries may leak or be damaged.

PREPARATION

Unpacking Your P-touch Labeier

Check that the package contains the followings before using your P-touch

labeler.

PT-80

M tape cassette

Included items may differ by distribution.

Power Supply & Tape Cassettes

Remove the back cover by pressing in

the rough area at the top end of the

machine.

If a tape cassette Is already Installed,

remove It by pulling It straight up. Also, If

batteries are already Installed, remove

them.

• Make sure that the power Is turned off

when replacing batteries or tape

cassette.

Print head

Insert four new AAA-size alkaline

batteries (LR03), making sure that

their poles point in the correct

directions. Always replace all four

batteries at the same time using brand

new ones.

Insert a tape cassette, making sure that it snaps into place.

Tape guide

Cutter's edge

End of tape

Tape exit slot

• Make sure that the end of the tape feeds under the tape guides.

• Use only Brother M tapes with this machine.

Attach the back cover by inserting two

hooks at the bottom into the slots on

the machine, then pushing down

firmly on the cover until it snaps into

place.

• After you have installed the tape, feed

the tape ( -I- ) once and

then push In the tape cutter lever to cut

the tape.

Tape cutter lever

£ OPERATION

Keyboard & LCD

Size

----------------

Width

I ' I I I

A A

A/A

fiñA

---------------

Style

Cursor

--------------

i-! / / !

Num Lock

Print key

Preview key

Power key

Character keys

Shift key -

Caps key -

Num Lock key -

Symbol key -

Caps-

Caps Num

___

I I

ABC/IÂBCl

■ Underllne/Frame

— Label Length

\ 'ia) (S) ©' ©* ©' ©' ©' ©' I ! if Backspace key

-r. © © © © © © © © © ©/ /

TIme/Date key

Function ke

Cursor key

/ \v

Function key

, ® © © © © © © ® © ©/

^.V.©.®.©.®.® ®.® 0.0/

brotler H^/y

■ Shift key

Enter key

- Accent key

Space key

The LCD shows one row of 12 characters; however, the text that

you enter can be up to 80 characters in length, which will scroll

across the display.

Use Cursor key while holding down Shift key to go to beginning /

end of the text.

Initial Setting

Start your machine

Supply power by using four AAA batteries, and then press (@

Set the language (English/Spanish/French/Portuguese)

* English *

Choose a language with II ^J) and press

Set the unit (inch/mm)

inch

T Choose a unit with C"* II *•]) and press ( —' ) .

Set Date (MM/DD/YY) and Time (hh:mm)

Example: setting the clock to March 20th 2006, 10:30AM

Date (MM/DD/YY)

input “03”

Time (hh:mm)

I hh:00 I

input “10”

input “20”

input “30”

input “06”

Select AM/PM with II and press ( ).

You can also confirm the figure and move to the next setting by using

right cursor key.

• The machine automatically turns off if no key is pressed within 5

minutes.

• To cancel operations, press @).

• To initialize the P-touch labeler back to factory settings, turn off the

machine and then while holding down //wf// and press to

turn the machine back on. Finally, release / and

[GETTING STARTED]

Troubleshooting

REFERENCE

Error message

Message Cause/Remedy

Battery

The batteries are weak.

Replace them with new ones.

Invalid Invalid number is selected for Label Length setting.

No Text • The Print key or Preview key is pressed when no text is

entered.

• You tried to set Copies (copy printing) when no text is

entered.

Line Lmt Line Limit. Printable lines are limited up to 2 lines.

You tried to enter a 3rd line by pressing Enter key.

Full The maximum number of characters (80 characters) have

already been entered.

Text Lmt Text Limit. The text length exceeds the selected label length

or the selected Auto Format setting length.

What to do when...

Problem Solution

The display stays blank

after you have turned on

the machine.

• Check that the batteries are correctly inserted.

• If the batteries are weak, replace them.

Language setting of the

machine is incorrect.

• Turn off the machine and then while holding

down ©*7 and ©), press to turn the machine

back on. Finally, release ©© and ©).

• Note: The text and formats in the display are erased. Also,

the language, unit and clock settings will be cleared.

The machine does not

print, or the printed

characters are not

formed properly.

• Check that the tape cassette has been inserted correctly.

• If the tape cassette is empty, replace it.

• Check the cassette cover is properly closed.

The setting has cleared

on its own.

• The batteries may be weak. Replace them.

• When power is disconnected for more than two minutes,

all text & formats in the display will be lost. Language, unit

and clock settings will also be cleared.

A blank horizontal line

appears through the

printed label.

• There may be some dust on the print head. Remove the

tape cassette and use a dry cotton swab to gently wipe the

print head with an up-and-down motion.

The machine has

"locked up" (i.e., nothing

happens when a key is

pressed, even though

the machine is on).

• Turn off the machine, and then while holding

down /©// and ©), press to turn the machine

back on. Finally, release ©© and ©).

• Note: The text and formats in the display are erased. Also,

the language, unit and clock settings will be cleared.

The power turns off

when you try to print.

• The batteries may be weak. Replace them.

The tape does not feed

properly or the tape gets

stuck inside the machine.

• Check that the end of the tape feeds under the tape

guides.

• The cutter lever is used while printing. Do not touch the

cutter lever during printing.

All text and format

settings need to be

cleared to create a new

label.

• Press Backspace key while holding down Shift key, or go

into Function mode and select (©

Specifications

Item Specification

Dimensions 6.8" (W) X 4.0" (D) X 2.3" (H)

(172 mm (W) x 100 mm (D) x 58 mm (H))

Weight

0.5 lbs. (240 g) (without batteries and tape cassette)

Power supply Four AAA-size alkaline batteries (LR03)

Tape cassette Brother M tape (width):

0.35" (9 mm), 0.47" (12 mm)

See the attached “Supplies and Accessories Guide” for detailed info of tape

variation.

MAKING TEXT

DESIGNING LABELS

Switching Upper Case/Lower Case

©■►® ® © ®

Upper case (ON) Lower case (OFF)

R E C D abed

Caps

Entering Numbers

Num Lock ON Num Lock OFF

1 2 3

Num

Entering Symbols

Symbol) ^ (© ►]) . ^ . II 1 .

Group Symbols

" ' •

■ 5 ■ 5

\ /

¿ i *

-F

± =

( ) [ ]

< >

t \

Group Symbols

$ (t € £ ¥ ° /

" ^ • O A V J»

O A ^ ^ 13 tì

$ @ ^ ft ^ é ^

W U 'it ^ ^

To go to the next group, press (5^.

To cancel operations, press

Entering Accented Characters

(T) ^ (T) II >■]) ^ )

Accented Characters

ÂÀÂÀÆÂAAàÀ

ÇCC

D D

ÉÈÊË^ËÉÉ

[ ÎÎ I [ T i

LLl\L

N NN N

ÔÔÔ0ÔÔŒÔ

R R R

è é § § ft

TTR

ûùûügùoû

Ÿ Ÿ

z z z

Accented Characters

ààââæâ^âââ

ÇCC

d’ô d

éèêëçëéë

g g

i Ì î ï i T 1

lÎ U’

n n h ç

ôôô0ôôœô

r r i

s s § § ft

tîD

ÙÙ(JÜL[ÙÜÛ

ÿ ÿ

z z z

To cancel operations, press (^.

The order of accented characters differ by the selected LCD language.

Making Two Line Text

Move the cursor to where the second line starts and press i

Display Label image

OLbe^Jde-f

abc

def

Setting [Size]

(@+®)

Text Preview

PRINTING LABELS

^ (00 [Size] ( ^ (0B [Large] ( ^ )

[Large] [Small]

J.SMITH

Setting [Width]

[Normal]

[Width] ( —' ) '

[X2]

№)[x2100

[X1/2]

J.SMITH J.SIVIITH

Setting [Styie] (Vertical)

(©+©)

[Normal]

[Style]

[Bold]

[Vertical] (0©

[Outline]

J.SMITH

D©

[Shadow]

[Italic] [l+Bold] (Italic Bold)

J.SMITH

[l+Outl](ltalic Outline) [l+Shadow](ltalic Shadow) [Vertical]

TN J.

ITN

CO ^ — I- X

©■

[Off] [Undl] (Underline) [Round]

ABC ABC fAB^

[Callout] [Banner] [Wooden]

^TaBC] VABCl,^ ^ABC:i

Setting [Length]

(Labei Length)(AutD/i.2"-i2.o")

[Undl] ( —' )

[Candy]

.4 IF'')

[Length] C0Z) '

• You can also select the length by entering the length with ® ®.

• To return to [Auto], press ( space ).

Setting [A/F](Auto Format) (®+®‘)

You can choose label length from five formats to create labels for various

applications.

LCD Application Length

VCR VHS Cassette spine 5.5"

MiniDV Cassette spine 1.6"

Audio Cassette case spine 3.5"

File Tab File tab 3.2"

Divider Divider Tab 1.6"

To Clear

By pressing the backspace key you will delete a character.

(To delete a whole line of text, keep pressing the Backspace key)

To Clear All the Text and the Settings (®+®’)

Shift / + IfBSlj

This will not affect Time & Date or language settings.

You can preview the text before printing.

The LCD shows the whole text and the label length (inch/mm), then returns to the

original text.

Only the text can be previewed, not the font, style, size, underline/frame or any

additional features.

pGGding (Tape Feed)

Shift J +

The machine will feed 1.0” of tape, which may be needed when Installing a new tape

cassette.

Printing

• To cut off the label, push in the tape cutter lever on the upper-left corner of the

machine.

• To prevent damage to the tape, do not try to cut while the message "Print" or

"Feed" is displayed.

Using Copies

(®+®)

You can print up to 9 copies of each label.

You can also select the number of copies by entering with ® ~ ®.

COMPLETED LABELS

OO2|-Cr<Ol-C0

CM o o m

_______________

S05(8632)-4112

ü[fa®ïïîî V(s)irfe

<S)

DO NOT TOUCH

<<<< Ken Sampson >>>>

[email protected]

M Merry X'mas é

Peel the printed label from backing and apply the label.

Removing the Label Backing

This machine is equipped with a peeler that allows you to easily remove the

backing from labels.

El Insert the label, with the printed surface facing down, as far as possible

^ into the built-in peeler.

Fold back the label to the right and quickly pull out the label. The end of

the backing is separated from the label.

[CREATING LABELS]

USEFUL FUNCTIONS

Time & Date Function

(®+®)

You can insert the desired time and date to your text at the touch of a button.

8 Formats are available for printing time and date.

You can change the number of time/date by changing the clock setting.

To add Time & Date to your text:

Thne/Datej / bc 03-^20-^06_

The cursor should be positioned where you wish to insert the time & date.

To select the format of Time & Date:

+ M/D/V hm *

Format Description

Example

(March 20th 2006, 3:30PM)

M/D/Y Month/ Date/ Year

03/20/06

M/D/Y hm Month/ Date/ Year time

03/20/06 03:30PM

D/M/Y Date/ Month/ Year

20/03/06

D/M/Y hm Date/ Month/ Year time

20/03/06 03:30PM

D.M.Y Date. Month. Year

20.03.06

D.M.Y hm Date.Month.Year time

20.03.06 03:30PM

Y-M-D Year- Month- Date

06-03-20

Y-M-D hm Year- Month- Date time

06-03-20 03:30PM

To change the Clock Setting:

Example: setting the clock to March 20th 2006, 10:30AM

Setting Month (MM), Date (DD), Year (YY)

input “03” input “20”

Setting Hour (hh) and Minute (mm)

input “10”

input “30”

input “06”

Select AM/PM with || *■)) and press ■

You can also confirm the figure and move to the next setting by using right cursor key.

Function Shortcuts (®+@)~®’)

In addition to the basic steps to search for a function, PT-80 provides you with

function shortcuts so you can easily jump to a frequently used function just by

To confirm, press ( -> ) ■

Key Function

(§)

Size

Width

Style

©^

Underline/Frame

©^

Label Length

Key Function

©^

Auto Format

©^

Copies

©^

Time & Date

All Clear

Should you encounter any problems with your product, please do not

return your product to the store!

After referring to the User's guide, if you still need assistance, call Brother

Customer Service at:

Voice : 1-877-BROTHER(1-877-276-8437)

Web : www.brother.com

Fax : 1-901-379-1210

If you need to locate a service center, please call

1-877-BROTHER(1-877-276-8437) or visit US at

www.brother.com

USER'S GUIDE 1

Résumé du contenu

Page 1 - USER'S GUIDE

brother.OCDo o o a o o o o o' o" o“ oooooooooo ooooooooo 00(iuciMW*“«“***’'*”"PT-80 USER'S GUIDEEnglish/ EspañolPrinted in Ch

Plus de documents pour Imprimeurs Brother PT-80

Voir le document Brother PT-80 Manuel d'utilisateur

Brother PT-80 Manuel d'utilisateur (1 pages)

Brother PT-80 Manuel d'utilisateur (2 pages)

Brother PT-80 Manuel d'utilisateur (1 pages)

Commentaires sur ces manuels

Pas de commentaire

Brother PT-80 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Imprimeurs Brother PT-80. Brother PT-80 User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Imprimeurs Brother PT-80

Commentaires sur ces manuels

Produits connexes et manuels pour Imprimeurs Brother PT-80